Ivoclar Te- Econom Plus Intro Kit

• Excellent physical properties
• Good polishability
• High radiopacity
• Long working time

Light-curing, radiopaque hybrid composite. Te-Econom Plus has excellent physical properties and great polishability that makes it suitable for use in both anterior and posterior restorations. The high radiopacity allows easy identification in x-rays. Te-Econom Plus has a long working time that helps the clinical perform the dental procedure efficiently. Eco-Etch etching gel is composed of 37% phosphoric acid, having optimal handling characteristics and good etching effect on enamel and dentin. Te-Econom Bond is one bottle, one layer adhesive to be used with the total-etch technique.

 INDICATIONS:

• Restorations of Classes I to V
• Esthetic anterior restorations
• Posterior restoration of stress-bearing areas.

ADVANTAGES – 

• Excellent physical properties.
• Good polishability.
• High radiopacity.
• Long Working time.
• Proven Ivoclar Vivadent technology and quality.

COMPOSITION –

• Dimethacrylate and TEGDMA (22 wt%).
• The fillers include barium glass, ytterbium trifluoride, silicon dioxide and mixed oxide (76 wt% or 60 vol%).
• Additives, initiators, stabilizers, and pigments are additional contents (2 wt%).

Storage temperature 2–28 °C (36–82 °F)

• The particle size of the inorganic fillers is between 0.04 and 7 µm.
• The mean particle size is 850 nm.

CONTRAINDICATION

• If a dry working field cannot be established or the stipulated application technique cannot be applied.
  
• If a patient is known to be allergic to any of the ingredients.
• Direct pulp capping with Te-Econom Bond/Flow/Plus

SIDE- EFFECTS –

• In rare cases, ingredients may lead to sensitization.
• The products should not be used in such cases.
• To avoid possible irritation of the pulp, areas close to the pulp should be protected with a suitable pulp/dentin protector

• 4 x 4 g Te-Econom plus syringes (A1/A2/A3/B2)
• 1 x 5 g Te-Econom Bond
• 1 x 2 g Eco-Etch

STEP 1- Select the shade. Establish sufficient isolation, preferably with a rubber dam.

STEP 2-Prepare the cavity according to the requirements of the adhesive technique. Clean the cavity with water spray. Air dry the cavity.

STEP 3-Apply a pulp protector (calcium hydroxide) if needed; only cover areas close to the pulp and subsequently apply a pressure-resistant cement (e.g. Vivaglass Liner).

STEP 4-Place a matrix (e.g. the selectively thinned OptraMatrix) and an interdental wedge, if required.

STEP 5- Apply Eco-Etch on the enamel and then on dentin and allow a reaction time of 30 seconds on enamel and 15 seconds on dentin. After that, thoroughly rinse with water spray and dry the tooth surfaces with oil-free compressed air. Avoid dehydrating the dentin.

STEP 6- Apply a generous amount of Te-Econom Bond on enamel and dentin, using the enclosed applicator brush. Brush the material gently into the dentin for 10 s. Next, evaporate any remaining solvent with a slow stream of air. Light cure the adhesive according to the curing time recommendations below. Ensure complete coverage of the preparation surface.

STEP 7- Apply Te-Econom Flow in layers of a max. of 2 mm and light cure according to the curing recommendations below. Apply Te-Econom Plus in layers of max. 2 mm and adapt/contour the material with a suitable instrument (e.g. OptraSculpt). The OptraContact instrument can be used to selectively position high-quality proximal contacts. Polymerize each layer individually according to the table below. Hold the light emission window as closely as possible to the surface of the restorative material.

STEP 8- Finish the restoration with suitable finishers or fine diamonds. Subsequently, check the occlusion. Polish with silicone polishers (e.g. OptraPol Next Generation).